There are several WAL-related configuration parameters that affect database performance. This section explains their use. Consult Chapter 18 for general information about setting server configuration parameters.
Checkpoints are points in the sequence of transactions at which it is guaranteed that the heap and index data files have been updated with all information written before the checkpoint. At checkpoint time, all dirty data pages are flushed to disk and a special checkpoint record is written to the log file. (The changes were previously flushed to the WAL files.) In the event of a crash, the crash recovery procedure looks at the latest checkpoint record to determine the point in the log (known as the redo record) from which it should start the REDO operation. Any changes made to data files before that point are guaranteed to be already on disk. Hence, after a checkpoint, log segments preceding the one containing the redo record are no longer needed and can be recycled or removed. (When WAL archiving is being done, the log segments must be archived before being recycled or removed.)
The checkpoint requirement of flushing all dirty data pages to disk can cause a significant I/O load. For this reason, checkpoint activity is throttled so I/O begins at checkpoint start and completes before the next checkpoint starts; this minimizes performance degradation during checkpoints.
The server's checkpointer process automatically performs a checkpoint every so often. A checkpoint is created every checkpoint_segments log segments, or every checkpoint_timeout seconds, whichever comes first. The default settings are 3 segments and 300 seconds (5 minutes), respectively. In cases where no WAL has been written since the previous checkpoint, new checkpoints will be skipped even if checkpoint_timeout has passed. If WAL archiving is being used and you want to put a lower limit on how often files are archived in order to bound potential data loss, you should adjust archive_timeout parameter rather than the checkpoint parameters. It is also possible to force a checkpoint by using the SQL command CHECKPOINT.
Reducing checkpoint_segments and/or checkpoint_timeout causes checkpoints to occur more often. This allows faster after-crash recovery (since less work will need to be redone). However, one must balance this against the increased cost of flushing dirty data pages more often. If full_page_writes is set (as is the default), there is another factor to consider. To ensure data page consistency, the first modification of a data page after each checkpoint results in logging the entire page content. In that case, a smaller checkpoint interval increases the volume of output to the WAL log, partially negating the goal of using a smaller interval, and in any case causing more disk I/O.
Checkpoints are fairly expensive, first because they require writing out all currently dirty buffers, and second because they result in extra subsequent WAL traffic as discussed above. It is therefore wise to set the checkpointing parameters high enough that checkpoints don't happen too often. As a simple sanity check on your checkpointing parameters, you can set the checkpoint_warning parameter. If checkpoints happen closer together than checkpoint_warning seconds, a message will be output to the server log recommending increasing checkpoint_segments. Occasional appearance of such a message is not cause for alarm, but if it appears often then the checkpoint control parameters should be increased. Bulk operations such as large COPY transfers might cause a number of such warnings to appear if you have not set checkpoint_segments high enough.
To avoid flooding the I/O system with a burst of page writes, writing dirty buffers during a checkpoint is spread over a period of time. That period is controlled by checkpoint_completion_target, which is given as a fraction of the checkpoint interval. The I/O rate is adjusted so that the checkpoint finishes when the given fraction of checkpoint_segments WAL segments have been consumed since checkpoint start, or the given fraction of checkpoint_timeout seconds have elapsed, whichever is sooner. With the default value of 0.5, PostgreSQL can be expected to complete each checkpoint in about half the time before the next checkpoint starts. On a system that's very close to maximum I/O throughput during normal operation, you might want to increase checkpoint_completion_target to reduce the I/O load from checkpoints. The disadvantage of this is that prolonging checkpoints affects recovery time, because more WAL segments will need to be kept around for possible use in recovery. Although checkpoint_completion_target can be set as high as 1.0, it is best to keep it less than that (perhaps 0.9 at most) since checkpoints include some other activities besides writing dirty buffers. A setting of 1.0 is quite likely to result in checkpoints not being completed on time, which would result in performance loss due to unexpected variation in the number of WAL segments needed.
There will always be at least one WAL segment file, and will normally not be more than (2 + checkpoint_completion_target) * checkpoint_segments + 1 or checkpoint_segments + wal_keep_segments + 1 files. Each segment file is normally 16 MB (though this size can be altered when building the server). You can use this to estimate space requirements for WAL. Ordinarily, when old log segment files are no longer needed, they are recycled (renamed to become the next segments in the numbered sequence). If, due to a short-term peak of log output rate, there are more than 3 * checkpoint_segments + 1 segment files, the unneeded segment files will be deleted instead of recycled until the system gets back under this limit.
In archive recovery or standby mode, the server periodically performs restartpoints which are similar to checkpoints in normal operation: the server forces all its state to disk, updates the pg_control file to indicate that the already-processed WAL data need not be scanned again, and then recycles any old log segment files in pg_xlog directory. A restartpoint is triggered if at least one checkpoint record has been replayed and checkpoint_timeout seconds have passed since last restartpoint. In standby mode, a restartpoint is also triggered if checkpoint_segments log segments have been replayed since last restartpoint and at least one checkpoint record has been replayed. Restartpoints can't be performed more frequently than checkpoints in the master because restartpoints can only be performed at checkpoint records.
There are two commonly used internal WAL functions:
is used to place a new record into the WAL buffers in shared memory. If there is no
space for the new record,
will have to write (move to kernel cache) a few filled
WAL buffers. This is undesirable
LogInsert is used on every
database low level modification (for example, row insertion) at a
time when an exclusive lock is held on affected data pages, so the
operation needs to be as fast as possible. What is worse, writing
WAL buffers might also force the
creation of a new log segment, which takes even more time.
Normally, WAL buffers should be
written and flushed by a
request, which is made, for the most part, at transaction commit
time to ensure that transaction records are flushed to permanent
storage. On systems with high log output,
LogFlush requests might not occur often enough to
LogInsert from having to do
writes. On such systems one should increase the number of
WAL buffers by modifying the
configuration parameter wal_buffers. When
is set and the system is very busy, setting this value higher will
help smooth response times during the period immediately following
parameter defines for how many microseconds the server process will
sleep after writing a commit record to the log with
LogInsert but before performing a
LogFlush. This delay allows other server
processes to add their commit records to the log so as to have all
of them flushed with a single log sync. No sleep will occur if
fsync is not
enabled, or if fewer than commit_siblings
other sessions are currently in active transactions; this avoids
sleeping when it's unlikely that any other session will commit
soon. Note that on most platforms, the resolution of a sleep
request is ten milliseconds, so that any nonzero commit_delay setting between 1 and 10000
microseconds would have the same effect. Good values for these
parameters are not yet clear; experimentation is encouraged.
The wal_sync_method parameter determines how PostgreSQL will ask the kernel to force WAL updates out to disk. All the options should be the same in terms of reliability, with the exception of fsync_writethrough, which can sometimes force a flush of the disk cache even when other options do not do so. However, it's quite platform-specific which one will be the fastest; you can test option speeds using the pg_test_fsync module. Note that this parameter is irrelevant if fsync has been turned off.
Enabling the wal_debug
configuration parameter (provided that PostgreSQL has been compiled with support for
it) will result in each
LogFlush WAL call being logged to the server log. This
option might be replaced by a more general mechanism in the